
Increase the value of your property with a beautiful new door. From entry, patio, and storm doors, we offer a variety of custom options.
Trusted by Thousands of Homeowners Across Northern California
We replace front doors, patio sliders, French doors, interior doors, and commercial entries across Sacramento with installs that seal on all four sides and latch into reinforced strikes. GVD crews handle measurement, removal, sealing, and finish trim under California Contractor License #989637.
Sacramento heat and UV degrade paint, stain, and weatherstrip from the outside in, especially on south and west-facing entries. Watch for these symptoms:
Fiberglass, steel, and solid wood entry doors from Therma-Tru, set with reinforced strike plates and graded deadbolts as standard. Fiberglass resists warping and dents and never needs refinishing.
Aluminum sliders are among the largest energy losers in a Sacramento home. We replace them with Anlin, Milgard, and Andersen sliders running dual-pane Low-E glass, tandem rollers, and full-perimeter weatherstrip.
Two operable swinging panels replace a slider for dining rooms, primary suites, and home offices. We set inswing or outswing, single or double, with a center astragal and optional multi-point locks.
Storm doors extend the life of an entry door against sun and rain. Heavy-gauge steel security doors carry reinforced strikes and a 1-inch-plus deadbolt throw.
Insulated steel or fiberglass units serve side-yard, back, and garage-to-house openings. The garage-to-living-space door is fire-rated per code, with keyed locking standard.
The choice turns on the condition of your jamb, threshold, and rough opening. We assess all three during the in-home measurement and tell you which path fits your opening.
Slab replacement keeps the existing jamb, threshold, and hinges. We hang a new pre-machined slab, swap the weatherstrip, and adjust the strike.
Full-frame replacement removes the entire pre-hung unit. The new unit goes in shimmed plumb, flashed, foam-sealed, and trimmed inside and out.
For doors over 15 years old, full-frame is usually the right call. It is the only method that resolves air-leak and threshold problems.
Pricing below covers the door, hardware, labor, disposal, weatherstripping, and trim work in one itemized quote.
| Door type | Installed price |
|---|---|
| Entry door, fiberglass or steel | $1,500 to $4,500 |
| Premium fiberglass or solid wood entry with decorative glass | $4,500 to $9,000+ |
| Patio slider (by size and brand) | $2,500 to $7,500 |
| Interior solid-core door | $400 to $900 each |
Labor to hang a door runs roughly $40 to $90 per hour for a licensed Sacramento carpenter, or about $150 to $500 for a standard slab swap. Homeowners report paying roughly $300 to $600 in labor to hang a pre-hung interior door, and $800 to $1,500 for an exterior door swap.
A like-for-like replacement that keeps the opening size usually needs no permit. Adding a new exterior door, enlarging an opening, or removing a section of wall does require a permit. We pull permits with the City of Sacramento, Sacramento County, or your local jurisdiction as part of our scope.
California exempts detached one-story accessory structures of 120 square feet or less from a building permit under the California Residential Code.
GVD holds an A+ BBB rating and a 4.9 of 5 average across 921+ verified Google and Yelp reviews. We serve Sacramento, Elk Grove, Folsom, Roseville, Rocklin, Granite Bay, El Dorado Hills, Lincoln, and Davis.
A slab swap finishes in 3 to 5 hours. A full-frame entry door runs 5 to 8 hours. A patio slider takes 6 to 10 hours, longer if the opening size changes. Interior doors run 1 to 2 hours each, so a 10-door whole-home project wraps in 2 to 3 days.
Fiberglass is the best all-around pick for most Sacramento homes. Steel suits back, side, and garage-to-house doors where security matters most. Solid wood only makes sense under a deep covered porch shaded from direct sun.
Yes. Cutting a new exterior opening requires a building permit for structural and energy-code review. A direct replacement that keeps the same opening usually does not.
Common rejection reasons include incomplete structural details for header sizing, work in a setback or easement, missing Title 24 energy compliance for new exterior openings, and HOA or historic-district restrictions. We submit complete plans to avoid these.
The manufacturer covers the door itself; Anlin, Milgard, Andersen, and Therma-Tru each run warranty programs that vary by product line. GVD covers workmanship: if a hinge sags, a seal fails, or the door binds because of how it was installed, we return and correct it.
Yes. Our crews also handle window replacement, siding, roofing, decking, and kitchen and bathroom remodeling. When doors are part of a larger scope, we sequence trim, paint, and finish work on one schedule.
Evaluate any installer on three checks: an active CSLB license, proof of workers' comp and liability insurance, and verified Google or Yelp review volume. GVD Renovations meets all three under License #989637. Confirm the company inspects your opening before quoting and includes trim and sealing in writing.







